Cisco胖AP配置,思科胖AP配置,思科AP配置,思科AP常用配置,思科AP配置实例
主要配置命令
hostname ap /设置AP名
dot11 ssid AP-N2 /设置SSID(AP-N2为SSID号)
authentication open /认证开放
authentication key-management wpa version 2 /认证密钥版本为WPA版本2
guest-mode /显示SSID,no guest-mode表示隐藏SSID
wpa-psk ascii 123456789 /SSID登陆密钥设置(123456789为密钥)
exit
exit
interface dot11radio0 /进入2.4G接口
encryption mode ciphers aes-ccm /加密密码AES CCM模式
ssid AP-N2 /加入SSID AP-N2
power local maximum /设置AP信号发射功率,默认可不配置
no shutdown /开启端口
exit
exit
interface dot11radio1 /进入5.8G接口
encryption mode ciphers aes-ccm /加密密码AES CCM模式
ssid AP-N2 /加入SSID AP-N2
power local maximum /设置AP信号发射功率,默认可不配置
no shutdown /开启端口
exit
exit
interface BVI1 进入管理接口
ip address 192.168.0.191 255.255.255.0 /配置接口IP地址
no shutdown /开启端口
ip default-gateway 192.168.0.1 /配置网关
配置范例
version 15.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
!
hostname test-ap
!
logging rate-limit console 9
enable secret 5 $5$4fXI$i1Zl2wBy24uDQd2j2Tuf41
!
no aaa new-model
clock timezone BeiJing 8 0
no ip source-route
no ip cef
!
dot11 syslog
!
dot11 ssid testssid
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 1443130D010939102541
!
dot11 guest
!
username myname secret 5 $4$7p8Z$yjeef33iW422J3bDrdN8Q/
!
bridge irb
!
interface Dot11Radio0
no ip address
no shutdown
!
encryption mode ciphers aes-ccm
!
ssid testssid
!
antenna gain 0
power local maximum
packet retries 64 drop-packet
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
!
encryption mode ciphers aes-ccm
!
ssid testssid
!
no shutdown
!
antenna gain 0
power local maximum
peakdetect
dfs band 3 block
packet retries 64 drop-packet
bridge-group 1
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
!
interface GigabitEthernet1
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 192.168.0.16 255.255.255.0
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
!
ip default-gateway 192.168.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
snmp-server community public RO
bridge 1 route ip
!
line con 0
line vty 0 4
login local
transport input all
!
sntp server 192.168.0.1
end