欢迎来访~

Cisco 4507交换机升级IOS

由于现有的4507 ios存在bug,现通过升级ios来修复。
升级前IOS版本信息:cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
升级后IOS版本信息:cat4500e-universal.SPA.03.08.10.E.152-4.E10.bin
由于IOS版本比较新,对应的ROM也需要升级。
升级前ROM版本信息:cat4500-e-ios-promupgrade-150-1r-SG5
升级后ROM版本信息:cat4500-e-ios-promupgrade-150-1r-SG10

1.设备运行状态检查

通过设备运行状态检查命令,记录设备运行现状,以备升级前后对比
show version
show bootvar
show cdp neighbors
show interfaces status
show ip interfaces brief
show etherchannel summary
show processes cpu | ex 0.00
show processes memory | in sed
show module
show environment status
show logging
show run
 

2.备份配置

原设备配置备份包括两部分,IOS软件和设备配置。
将IOS导出到固定的外部存储介质,已完成。
将运行配置导出到固定的外部存储介质:
WL-4507#copy running-config: tftp:
Address or name of remote host []? 192.168.2.55
Source filename []?172.17.10.2_WL-4507.log
Destination filename [172.17.10.2_WL-4507.log]?
 

3.引擎容量和寄存值检查

WL-4507# show version
……
Configuration register is 0x2102
 

4.将新的IOS和ROM文件上传至引擎

WL-4507#copy tftp: bootflash:
Address or name of remote host []? 192.168.2.55
Source filename []?cat4500e-universal.SPA.03.08.10.E.152-4.E10.bin
Destination filename [cat4500e-universal.SPA.03.08.10.E.152-4.E10.bin]?
 
WL-4507#copy tftp: bootflash:
Address or name of remote host []? 192.168.2.55
Source filename []?cat4500-e-ios-promupgrade-150-1r-SG10
Destination filename [cat4500-e-ios-promupgrade-150-1r-SG10]?
 

5.配置并检查设备启动参数

WL-4507#conf t
WL-4507(config)#no boot system bootflash:cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
WL-4507(config)#boot system flash bootflash:cat4500-e-ios-promupgrade-150-1r-SG10
WL-4507(config)#boot system flash bootflash:cat4500e-universal.SPA.03.08.10.E.152-4.E10.bin
WL-4507(config)#config-register 0x2102
WL-4507#write
WL-4507#show bootvar
 

6.重启

确定bootvar和寄存器值没有问题后,重新启动。
WL-4507# reload
手动重启后设备会先升级ROM,ROM升级完成第二次自动重启,第二次自动重启时会把ROM再升级一遍,再加载新IOS,最后进入系统。
重启时间大概10分钟左右。
 

7.升级后的检查

WL-4507# show version
WL-4507#conf t
WL-4507(config)#no boot system flash bootflash: cat4500-e-ios-promupgrade-150-1r-SG10
WL-4507# show bootvar
WL-4507#write
将检查命令再次检查一遍。
使用对比工具对比升级前后的配置文件,查看是否有配置丢失或者改动的地方。
至此,升级完成!
 

附:回退实施步骤

修改启动引导参数
WL-4507(config)#no boot system flash bootflash: cat4500e-universal.SPA.03.08.10.E.152-4.E10.bin
WL-4507(config)#boot system flash bootflash: cat4500-e-ios-promupgrade-150-1r-SG5
WL-4507(config)#boot system flash bootflash: cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
重新启动当前设备
WL-4507# reload
配置验证与网络测试验证
将回退IOS后的配置与升级IOS前的配置进行核对比较,确保当前设备回退到可以正常运行的状态。
 
此次升级所需要的IOS和ROM文件我还存着,如果有恰好需要的可以通过右下角QQ临时会话或评论留言。
 
赞(6)
可附来源转载:一只北极熊 » Cisco 4507交换机升级IOS

富强、民主、文明、和谐、自由、平等、公正、法治、爱国、敬业、诚信、友善